Packet tracer activity wizard 6.2 Pc#

NetEss v1 Packet Tracer Activity Source Files Answers.

NE 2.0 Packet Tracer Activity Lab Answers.

ITN v6 Student Lab Source Files Answers.

ITE v7 Student Lab Source Files Answers.

ITE v6 Student Packet Tracer Source Files Answers.

ITE v6 Student Lab Source Files Answers.

DevNet вЂ“ DEVASC вЂ“ Packet Tracer Lab Answers.

Cybersecurity Student Lab Source Answers.

CyberOps AssociateвЂ“ CA вЂ“ Packet Tracer Answers.

CyberEss v1 Student Lab Source Files Answers.

CyberEss v1 Packet Tracer Activity Source Files Answers.

CCNA3 v7 вЂ“ ENSA вЂ“ Packet Tracer Answers.

CCNA2 v7 вЂ“ SRWE вЂ“ Packet Tracer Answers.

Suggested Scoring Rubric Activity Section What could be done to resolve this issue? Configure the ports between the switches as trunk ports. Although the access ports are assigned to the appropriate VLANs, were the pings successful? Why? No, the pings failed because the ports between the switches are in VLAN 1 and PC1 and PC4 are in VLAN 10. Previously, PCs that shared the same network could ping each other successfully. S3(config)# interface f0/11 S3(config-if)# mls qos trust cos S3(config-if)# switchport voice vlan 150 S3(config-if)# end Step 4: Verify loss of connectivity. The interface must also enable QoS and trust the Class of Service (CoS) values assigned by the IP phone. The S3 F0/11 interface must be configured to support user traffic to PC4 using VLAN 10 and voice traffic to the IP phone using VLAN 150. The IP phone also has an internal port that connects to the IP phone functions.

Packet tracer activity wizard 6.2 Pc#

Another port on the phone is labeled PC and connects to PC4. One port on the phone is labeled Switch and connects to F0/4. The IP phone contains an integrated three-port 10/100 switch. S3(config)# interface f0/11 S3(config-if)# switchport mode access S3(config-if)# switchport access vlan 10 S3(config-if)# interface f0/18 S3(config-if)# switchport mode access S3(config-if)# switchport access vlan 20 S3(config-if)# interface f0/6 S3(config-if)# switchport mode access S3(config-if)# switchport access vlan 30 Step 3: Assign the VOICE VLAN to FastEthernet 0/11 on S3.ДЄs shown in the topology, the S3 FastEthernet 0/11 interface connects to a Cisco IP Phone and PC4. Configure the interfaces as access ports and assign the VLANs as follows: S3 uses the same VLAN access port assignments as S2. S2(config)# interface f0/11 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 10 S2(config-if)# interface f0/18 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 20 S2(config-if)# interface f0/6 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 30 Step 2: Assign VLANs to the active ports on S3. Part 3: Assign VLANs to Ports Step 1: Assign VLANs to the active ports on S2.Д¬onfigure the interfaces as access ports and assign the VLANs as follows: Using the same commands from Step 1, create and name the same VLANs on S2 and S3. S1# show vlan brief Step 3: Create the VLANs on S2 and S3. Which command will only display the VLAN name, status, and associated ports on a switch? S1#(config)# vlan 10 S1#(config-vlan)# name Faculty/Staff S1#(config-vlan)# vlan 20 S1#(config-vlan)# name Students S1#(config-vlan)# vlan 30 S1#(config-vlan)# name Guest(Default) S1#(config-vlan)# vlan 99 S1#(config-vlan)# name Management&Native S1#(config-vlan)# vlan 150 S1#(config-vlan)# name VOICE Step 2: Verify the VLAN configuration. Part 2: Configure VLANs Step 1: Create and name VLANs on S1.Д¬reate the following VLANs. What benefit will configuring VLANs provide to the current configuration? The primary benefits of using VLANs are as follows: security, cost reduction, higher performance, broadcast storm mitigation, improved IT staff efficiency, and simpler project and application management. Notice that each PC can ping the other PC that shares the same network. Step 2: Verify connectivity between PCs on the same network. By default, all interfaces are assigned to VLAN 1.

On S1, issue the command that displays all VLANs configured. Part 1: View the Default VLAN Configuration Step 1: Display the current VLANs. This activity focuses on creating and naming VLANs, and assigning access ports to specific VLANs. VLANs are helpful in the administration of logical groups, allowing members of a group to be easily moved, changed, or added. Part 1: Verify the Default VLAN Configuration 6.2.1.7 Packet Tracer вЂ“ Configuring VLANs Addressing Table Device